14.04 wifi disconnect reason 2
Ubuntu 14.04
HW: rt2860 (I'm sure since is my eeepc 1000he) BUT seen from ubuntu as rt2890
lspci:
01:00.0 Network controller: Ralink corp. RT2790 Wireless 802.11n 1T/2R PCIe
module: rt28000pci
It's a wep connection, it connect just for a couple of minutes, then disconnect with reason 2, here just a few lines from dmesg.
[ 238.999880] wlan0: authenticate with e0:91:53:25:0b:f1
[ 239.012788] wlan0: send auth to e0:91:53:25:0b:f1 (try 1/3)
[ 239.019096] wlan0: authenticated
[ 239.019814] rt2800pci 0000:01:00.0 wlan0: disabling HT/VHT due to WEP/TKIP use
[ 239.019836] rt2800pci 0000:01:00.0 wlan0: disabling HT as WMM/QoS is not supported by the AP
[ 239.019850] rt2800pci 0000:01:00.0 wlan0: disabling VHT as WMM/QoS is not supported by the AP
[ 239.020176] wlan0: associate with e0:91:53:25:0b:f1 (try 1/3)
[ 239.022206] wlan0: RX AssocResp from e0:91:53:25:0b:f1 (capab=0x431 status=0 aid=17)
[ 239.023239] wlan0: associated
[ 239.023345] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 239.063810] wlan0: deauthenticated from e0:91:53:25:0b:f1 (Reason: 2)
[ 240.025701] wlan0: authenticate with e0:91:53:25:0b:f1
[ 240.028223] wlan0: send auth to e0:91:53:25:0b:f1 (try 1/3)
[ 240.032416] wlan0: authenticated
With open networks it works without problems, I'll check with WPA as soon as I can.
Any idea?
wireless drivers 14.04 disconnect
asked Jun 21 '14 at 18:01
ElwoodElwood
611
bumped to the homepage by Community♦ 10 mins ago
This question has answers that may be good or bad; the system has marked it active so that they can be reviewed.
|
show 1 more comment
Ubuntu 14.04
HW: rt2860 (I'm sure since is my eeepc 1000he) BUT seen from ubuntu as rt2890
lspci:
01:00.0 Network controller: Ralink corp. RT2790 Wireless 802.11n 1T/2R PCIe
module: rt28000pci
It's a wep connection, it connect just for a couple of minutes, then disconnect with reason 2, here just a few lines from dmesg.
[ 238.999880] wlan0: authenticate with e0:91:53:25:0b:f1
[ 239.012788] wlan0: send auth to e0:91:53:25:0b:f1 (try 1/3)
[ 239.019096] wlan0: authenticated
[ 239.019814] rt2800pci 0000:01:00.0 wlan0: disabling HT/VHT due to WEP/TKIP use
[ 239.019836] rt2800pci 0000:01:00.0 wlan0: disabling HT as WMM/QoS is not supported by the AP
[ 239.019850] rt2800pci 0000:01:00.0 wlan0: disabling VHT as WMM/QoS is not supported by the AP
[ 239.020176] wlan0: associate with e0:91:53:25:0b:f1 (try 1/3)
[ 239.022206] wlan0: RX AssocResp from e0:91:53:25:0b:f1 (capab=0x431 status=0 aid=17)
[ 239.023239] wlan0: associated
[ 239.023345] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 239.063810] wlan0: deauthenticated from e0:91:53:25:0b:f1 (Reason: 2)
[ 240.025701] wlan0: authenticate with e0:91:53:25:0b:f1
[ 240.028223] wlan0: send auth to e0:91:53:25:0b:f1 (try 1/3)
[ 240.032416] wlan0: authenticated
With open networks it works without problems, I'll check with WPA as soon as I can.
Any idea?
wireless drivers 14.04 disconnect
asked Jun 21 '14 at 18:01
ElwoodElwood
611
bumped to the homepage by Community♦ 10 mins ago
This question has answers that may be good or bad; the system has marked it active so that they can be reviewed.
Reason 2 means Previous authentication no longer valid i.e., Client has associated but is not authorised
– Raphael
Jun 21 '14 at 18:06
@Raphael, great, how can I see what's is going bad? With archlinux it worked, same essid, same wep key (and it's working right now with android)
– Elwood
Jun 21 '14 at 18:25
Can you see the properties of your WEP wifi connection like is it WEP 128/40 bit OR 128bit?
– Raphael
Jun 21 '14 at 18:30
Sure, on network-manager profiles is WEP 128/40 on the router is Security : 128 bit WEP
– Elwood
Jun 21 '14 at 18:35
Then delete all the existing wi-fi connections and create a new one from Network Connections.
– Raphael
Jun 21 '14 at 18:37
|
show 1 more comment
Ubuntu 14.04
HW: rt2860 (I'm sure since is my eeepc 1000he) BUT seen from ubuntu as rt2890
lspci:
01:00.0 Network controller: Ralink corp. RT2790 Wireless 802.11n 1T/2R PCIe
module: rt28000pci
It's a wep connection, it connect just for a couple of minutes, then disconnect with reason 2, here just a few lines from dmesg.
[ 238.999880] wlan0: authenticate with e0:91:53:25:0b:f1
[ 239.012788] wlan0: send auth to e0:91:53:25:0b:f1 (try 1/3)
[ 239.019096] wlan0: authenticated
[ 239.019814] rt2800pci 0000:01:00.0 wlan0: disabling HT/VHT due to WEP/TKIP use
[ 239.019836] rt2800pci 0000:01:00.0 wlan0: disabling HT as WMM/QoS is not supported by the AP
[ 239.019850] rt2800pci 0000:01:00.0 wlan0: disabling VHT as WMM/QoS is not supported by the AP
[ 239.020176] wlan0: associate with e0:91:53:25:0b:f1 (try 1/3)
[ 239.022206] wlan0: RX AssocResp from e0:91:53:25:0b:f1 (capab=0x431 status=0 aid=17)
[ 239.023239] wlan0: associated
[ 239.023345] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 239.063810] wlan0: deauthenticated from e0:91:53:25:0b:f1 (Reason: 2)
[ 240.025701] wlan0: authenticate with e0:91:53:25:0b:f1
[ 240.028223] wlan0: send auth to e0:91:53:25:0b:f1 (try 1/3)
[ 240.032416] wlan0: authenticated
With open networks it works without problems, I'll check with WPA as soon as I can.
Any idea?
wireless drivers 14.04 disconnect
asked Jun 21 '14 at 18:01
ElwoodElwood
611
Ubuntu 14.04
HW: rt2860 (I'm sure since is my eeepc 1000he) BUT seen from ubuntu as rt2890
lspci:
01:00.0 Network controller: Ralink corp. RT2790 Wireless 802.11n 1T/2R PCIe
module: rt28000pci
It's a wep connection, it connect just for a couple of minutes, then disconnect with reason 2, here just a few lines from dmesg.
[ 238.999880] wlan0: authenticate with e0:91:53:25:0b:f1
[ 239.012788] wlan0: send auth to e0:91:53:25:0b:f1 (try 1/3)
[ 239.019096] wlan0: authenticated
[ 239.019814] rt2800pci 0000:01:00.0 wlan0: disabling HT/VHT due to WEP/TKIP use
[ 239.019836] rt2800pci 0000:01:00.0 wlan0: disabling HT as WMM/QoS is not supported by the AP
[ 239.019850] rt2800pci 0000:01:00.0 wlan0: disabling VHT as WMM/QoS is not supported by the AP
[ 239.020176] wlan0: associate with e0:91:53:25:0b:f1 (try 1/3)
[ 239.022206] wlan0: RX AssocResp from e0:91:53:25:0b:f1 (capab=0x431 status=0 aid=17)
[ 239.023239] wlan0: associated
[ 239.023345] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 239.063810] wlan0: deauthenticated from e0:91:53:25:0b:f1 (Reason: 2)
[ 240.025701] wlan0: authenticate with e0:91:53:25:0b:f1
[ 240.028223] wlan0: send auth to e0:91:53:25:0b:f1 (try 1/3)
[ 240.032416] wlan0: authenticated
With open networks it works without problems, I'll check with WPA as soon as I can.
Any idea?
wireless drivers 14.04 disconnect
wireless drivers 14.04 disconnect
asked Jun 21 '14 at 18:01
ElwoodElwood
611
asked Jun 21 '14 at 18:01
ElwoodElwood
611
asked Jun 21 '14 at 18:01
ElwoodElwood
611
asked Jun 21 '14 at 18:01
ElwoodElwood
611
asked Jun 21 '14 at 18:01
ElwoodElwood
611
611
bumped to the homepage by Community♦ 10 mins ago
This question has answers that may be good or bad; the system has marked it active so that they can be reviewed.
bumped to the homepage by Community♦ 10 mins ago
This question has answers that may be good or bad; the system has marked it active so that they can be reviewed.
Reason 2 means Previous authentication no longer valid i.e., Client has associated but is not authorised
– Raphael
Jun 21 '14 at 18:06
@Raphael, great, how can I see what's is going bad? With archlinux it worked, same essid, same wep key (and it's working right now with android)
– Elwood
Jun 21 '14 at 18:25
Can you see the properties of your WEP wifi connection like is it WEP 128/40 bit OR 128bit?
– Raphael
Jun 21 '14 at 18:30
Sure, on network-manager profiles is WEP 128/40 on the router is Security : 128 bit WEP
– Elwood
Jun 21 '14 at 18:35
Then delete all the existing wi-fi connections and create a new one from Network Connections.
– Raphael
Jun 21 '14 at 18:37
|
show 1 more comment
Reason 2 means Previous authentication no longer valid i.e., Client has associated but is not authorised
– Raphael
Jun 21 '14 at 18:06
@Raphael, great, how can I see what's is going bad? With archlinux it worked, same essid, same wep key (and it's working right now with android)
– Elwood
Jun 21 '14 at 18:25
Can you see the properties of your WEP wifi connection like is it WEP 128/40 bit OR 128bit?
– Raphael
Jun 21 '14 at 18:30
Sure, on network-manager profiles is WEP 128/40 on the router is Security : 128 bit WEP
– Elwood
Jun 21 '14 at 18:35
Then delete all the existing wi-fi connections and create a new one from Network Connections.
– Raphael
Jun 21 '14 at 18:37
Reason 2 means Previous authentication no longer valid i.e., Client has associated but is not authorised
– Raphael
Jun 21 '14 at 18:06
Reason 2 means Previous authentication no longer valid i.e., Client has associated but is not authorised
– Raphael
Jun 21 '14 at 18:06
@Raphael, great, how can I see what's is going bad? With archlinux it worked, same essid, same wep key (and it's working right now with android)
– Elwood
Jun 21 '14 at 18:25
@Raphael, great, how can I see what's is going bad? With archlinux it worked, same essid, same wep key (and it's working right now with android)
– Elwood
Jun 21 '14 at 18:25
Can you see the properties of your WEP wifi connection like is it WEP 128/40 bit OR 128bit?
– Raphael
Jun 21 '14 at 18:30
Can you see the properties of your WEP wifi connection like is it WEP 128/40 bit OR 128bit?
– Raphael
Jun 21 '14 at 18:30
Sure, on network-manager profiles is WEP 128/40 on the router is Security : 128 bit WEP
– Elwood
Jun 21 '14 at 18:35
Sure, on network-manager profiles is WEP 128/40 on the router is Security : 128 bit WEP
– Elwood
Jun 21 '14 at 18:35
Then delete all the existing wi-fi connections and create a new one from Network Connections.
– Raphael
Jun 21 '14 at 18:37
Then delete all the existing wi-fi connections and create a new one from Network Connections.
– Raphael
Jun 21 '14 at 18:37
|
show 1 more comment
1 Answer
1
active
oldest
votes
Please run the following commands one line at a time and just copy and paste for accuracy:
echo "options rt2800pci nohwcrypt=1" | sudo tee /etc/modprobe.d/rt2800pci.conf
sudo modprobe -rfv rt2800pci
sudo modprobe -v rt2800pci
This command changes encryption from hardware to software and in many cases corrects the issue you are having.
Wep is not very secure and ubuntu will connect to wpa2 (AES) (CCMP) better then any other settings, not mixed mode or especially (TKIP).
answered Jun 21 '14 at 21:00
Wild ManWild Man
6,55232640
add a comment |
Your Answer
StackExchange.ready(function() {
var channelOptions = {
tags: "".split(" "),
id: "89"
};
initTagRenderer("".split(" "), "".split(" "), channelOptions);
StackExchange.using("externalEditor", function() {
// Have to fire editor after snippets, if snippets enabled
if (StackExchange.settings.snippets.snippetsEnabled) {
StackExchange.using("snippets", function() {
createEditor();
});
}
else {
createEditor();
}
});
function createEditor() {
StackExchange.prepareEditor({
heartbeatType: 'answer',
autoActivateHeartbeat: false,
convertImagesToLinks: true,
noModals: true,
showLowRepImageUploadWarning: true,
reputationToPostImages: 10,
bindNavPrevention: true,
postfix: "",
imageUploader: {
brandingHtml: "Powered by u003ca class="icon-imgur-white" href="https://imgur.com/"u003eu003c/au003e",
contentPolicyHtml: "User contributions licensed under u003ca href="https://creativecommons.org/licenses/by-sa/3.0/"u003ecc by-sa 3.0 with attribution requiredu003c/au003e u003ca href="https://stackoverflow.com/legal/content-policy"u003e(content policy)u003c/au003e",
allowUrls: true
},
onDemand: true,
discardSelector: ".discard-answer"
,immediatelyShowMarkdownHelp:true
});
}
});
Sign up or log in
StackExchange.ready(function () {
StackExchange.helpers.onClickDraftSave('#login-link');
});
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
StackExchange.ready(
function () {
StackExchange.openid.initPostLogin('.new-post-login', 'https%3a%2f%2faskubuntu.com%2fquestions%2f486442%2f14-04-wifi-disconnect-reason-2%23new-answer', 'question_page');
}
);
Post as a guest
Required, but never shown
1 Answer
1
active
oldest
votes
1 Answer
1
active
oldest
votes
active
oldest
votes
active
oldest
votes
Please run the following commands one line at a time and just copy and paste for accuracy:
echo "options rt2800pci nohwcrypt=1" | sudo tee /etc/modprobe.d/rt2800pci.conf
sudo modprobe -rfv rt2800pci
sudo modprobe -v rt2800pci
This command changes encryption from hardware to software and in many cases corrects the issue you are having.
Wep is not very secure and ubuntu will connect to wpa2 (AES) (CCMP) better then any other settings, not mixed mode or especially (TKIP).
answered Jun 21 '14 at 21:00
Wild ManWild Man
6,55232640
add a comment |
Please run the following commands one line at a time and just copy and paste for accuracy:
echo "options rt2800pci nohwcrypt=1" | sudo tee /etc/modprobe.d/rt2800pci.conf
sudo modprobe -rfv rt2800pci
sudo modprobe -v rt2800pci
This command changes encryption from hardware to software and in many cases corrects the issue you are having.
Wep is not very secure and ubuntu will connect to wpa2 (AES) (CCMP) better then any other settings, not mixed mode or especially (TKIP).
answered Jun 21 '14 at 21:00
Wild ManWild Man
6,55232640
add a comment |
Please run the following commands one line at a time and just copy and paste for accuracy:
echo "options rt2800pci nohwcrypt=1" | sudo tee /etc/modprobe.d/rt2800pci.conf
sudo modprobe -rfv rt2800pci
sudo modprobe -v rt2800pci
This command changes encryption from hardware to software and in many cases corrects the issue you are having.
Wep is not very secure and ubuntu will connect to wpa2 (AES) (CCMP) better then any other settings, not mixed mode or especially (TKIP).
answered Jun 21 '14 at 21:00
Wild ManWild Man
6,55232640
Please run the following commands one line at a time and just copy and paste for accuracy:
echo "options rt2800pci nohwcrypt=1" | sudo tee /etc/modprobe.d/rt2800pci.conf
sudo modprobe -rfv rt2800pci
sudo modprobe -v rt2800pci
This command changes encryption from hardware to software and in many cases corrects the issue you are having.
Wep is not very secure and ubuntu will connect to wpa2 (AES) (CCMP) better then any other settings, not mixed mode or especially (TKIP).
answered Jun 21 '14 at 21:00
Wild ManWild Man
6,55232640
answered Jun 21 '14 at 21:00
Wild ManWild Man
6,55232640
answered Jun 21 '14 at 21:00
Wild ManWild Man
6,55232640
answered Jun 21 '14 at 21:00
Wild ManWild Man
6,55232640
6,55232640
add a comment |
add a comment |
Thanks for contributing an answer to Ask Ubuntu!
- Please be sure to answer the question. Provide details and share your research!
But avoid …
- Asking for help, clarification, or responding to other answers.
- Making statements based on opinion; back them up with references or personal experience.
To learn more, see our tips on writing great answers.
Sign up or log in
StackExchange.ready(function () {
StackExchange.helpers.onClickDraftSave('#login-link');
});
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
StackExchange.ready(
function () {
StackExchange.openid.initPostLogin('.new-post-login', 'https%3a%2f%2faskubuntu.com%2fquestions%2f486442%2f14-04-wifi-disconnect-reason-2%23new-answer', 'question_page');
}
);
Post as a guest
Required, but never shown
Sign up or log in
StackExchange.ready(function () {
StackExchange.helpers.onClickDraftSave('#login-link');
});
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
Sign up or log in
StackExchange.ready(function () {
StackExchange.helpers.onClickDraftSave('#login-link');
});
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
Sign up or log in
StackExchange.ready(function () {
StackExchange.helpers.onClickDraftSave('#login-link');
});
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Reason 2 means Previous authentication no longer valid i.e., Client has associated but is not authorised
– Raphael
Jun 21 '14 at 18:06
@Raphael, great, how can I see what's is going bad? With archlinux it worked, same essid, same wep key (and it's working right now with android)
– Elwood
Jun 21 '14 at 18:25
Can you see the properties of your WEP wifi connection like is it WEP 128/40 bit OR 128bit?
– Raphael
Jun 21 '14 at 18:30
Sure, on network-manager profiles is WEP 128/40 on the router is Security : 128 bit WEP
– Elwood
Jun 21 '14 at 18:35
Then delete all the existing wi-fi connections and create a new one from Network Connections.
– Raphael
Jun 21 '14 at 18:37