Airplane gently rocking its wings during whole flight
$begingroup$
I was on a flight with a regional airline a while ago in a Bombardier airplane (if I recall correctly) where the airplane would slowly and gently rock its wings just a little bit on the whole flight. I wasn't a long flight but wasn't very short either at roughly 2 hours.
It was very comfortable and the rocking made for a very gentle cradle feeling 🙂
My question is, why would that be? Is it economical to do so for any reason? Is it possible that the airplane had no autopilot and the pilot was flying it by hand? What could cause such a behaviour?
aerodynamics wing economics
$endgroup$
add a comment |
$begingroup$
I was on a flight with a regional airline a while ago in a Bombardier airplane (if I recall correctly) where the airplane would slowly and gently rock its wings just a little bit on the whole flight. I wasn't a long flight but wasn't very short either at roughly 2 hours.
It was very comfortable and the rocking made for a very gentle cradle feeling 🙂
My question is, why would that be? Is it economical to do so for any reason? Is it possible that the airplane had no autopilot and the pilot was flying it by hand? What could cause such a behaviour?
aerodynamics wing economics
$endgroup$
$begingroup$
Sounds like the dutch roll mode was working. Were you high and fast at the time?
$endgroup$
– MikeY
2 hours ago
add a comment |
$begingroup$
I was on a flight with a regional airline a while ago in a Bombardier airplane (if I recall correctly) where the airplane would slowly and gently rock its wings just a little bit on the whole flight. I wasn't a long flight but wasn't very short either at roughly 2 hours.
It was very comfortable and the rocking made for a very gentle cradle feeling 🙂
My question is, why would that be? Is it economical to do so for any reason? Is it possible that the airplane had no autopilot and the pilot was flying it by hand? What could cause such a behaviour?
aerodynamics wing economics
$endgroup$
I was on a flight with a regional airline a while ago in a Bombardier airplane (if I recall correctly) where the airplane would slowly and gently rock its wings just a little bit on the whole flight. I wasn't a long flight but wasn't very short either at roughly 2 hours.
It was very comfortable and the rocking made for a very gentle cradle feeling 🙂
My question is, why would that be? Is it economical to do so for any reason? Is it possible that the airplane had no autopilot and the pilot was flying it by hand? What could cause such a behaviour?
aerodynamics wing economics
aerodynamics wing economics
asked 2 hours ago
Délisson JunioDélisson Junio
377414
377414
$begingroup$
Sounds like the dutch roll mode was working. Were you high and fast at the time?
$endgroup$
– MikeY
2 hours ago
add a comment |
$begingroup$
Sounds like the dutch roll mode was working. Were you high and fast at the time?
$endgroup$
– MikeY
2 hours ago
$begingroup$
Sounds like the dutch roll mode was working. Were you high and fast at the time?
$endgroup$
– MikeY
2 hours ago
$begingroup$
Sounds like the dutch roll mode was working. Were you high and fast at the time?
$endgroup$
– MikeY
2 hours ago
add a comment |
1 Answer
1
active
oldest
votes
$begingroup$
I can give you two theories. One is it's a very very mild case of "overcontrolling" of the autopilot roll servo as it chases a perfectly wings level condition and continuously applies a teeny bit too much left, ooops, then a teeny bit too much right, oops, and back and forth.
The aileron control circuit is cables running to hydraulics at the ailerons, with a spring loaded roller in a curvy V shaped cam device that centers each side of the aileron cable circuit. The breakout force to move the control circuit out of neutral (forcing the roller from the center V of the cam) is fairly high and this can actually be a problem for pilots hand flying at higher speeds where the ailerons are quite snappy - applying enough force to break out the circuit and move the wheel left gives too much, and back the other way... too much... and back and forth you go. It can be a pain.
The autopilot servo is basically a little electric winch connected into the aileron cable circuit, doing the same thing the pilot does. It could be that something in the electronic control loop, or mechanically within the servo, can cause this back and forth oscillation on some airplanes, sometimes. It may be related to wear and backlash within the autopilot servo.
The other theory is it's more or less something similar, but in the yaw mode with the yaw damper not able to fully dampen out a dutch roll mode because the amplitude was within the yaw damper's sensitivity band. Dutch roll is rolling due to yaw, which in swept wing jets is very strong, such that it can set up continuous self energizing oscillation. It could also be related to wear and backlash in the yaw damper actuator, which is a pair of electric linear actuators (little electric screw jacks), in the push rods going to the rudder hydraulics.
If you saw the wing tip just going straight up and down, it's mostly likely the first theory. If you could see the winglet moving in a little circle (indicating rolling and yawing), it's more likely the second theory.
I can really only theorize because the issue was never fully explored on the RJ program as this phenomenon was random, very minor and not dangerous, and was never complained about by operators because only someone sitting near the wings that can look straight out at the winglet ever notices it. It was never bad enough to get anyone sick for example, at least on the RJ fleet.
$endgroup$
add a comment |
StackExchange.ifUsing("editor", function () {
return StackExchange.using("mathjaxEditing", function () {
StackExchange.MarkdownEditor.creationCallbacks.add(function (editor, postfix) {
StackExchange.mathjaxEditing.prepareWmdForMathJax(editor, postfix, [["$", "$"], ["\\(","\\)"]]);
});
});
}, "mathjax-editing");
StackExchange.ready(function() {
var channelOptions = {
tags: "".split(" "),
id: "528"
};
initTagRenderer("".split(" "), "".split(" "), channelOptions);
StackExchange.using("externalEditor", function() {
// Have to fire editor after snippets, if snippets enabled
if (StackExchange.settings.snippets.snippetsEnabled) {
StackExchange.using("snippets", function() {
createEditor();
});
}
else {
createEditor();
}
});
function createEditor() {
StackExchange.prepareEditor({
heartbeatType: 'answer',
autoActivateHeartbeat: false,
convertImagesToLinks: false,
noModals: true,
showLowRepImageUploadWarning: true,
reputationToPostImages: null,
bindNavPrevention: true,
postfix: "",
imageUploader: {
brandingHtml: "Powered by u003ca class="icon-imgur-white" href="https://imgur.com/"u003eu003c/au003e",
contentPolicyHtml: "User contributions licensed under u003ca href="https://creativecommons.org/licenses/by-sa/3.0/"u003ecc by-sa 3.0 with attribution requiredu003c/au003e u003ca href="https://stackoverflow.com/legal/content-policy"u003e(content policy)u003c/au003e",
allowUrls: true
},
noCode: true, onDemand: true,
discardSelector: ".discard-answer"
,immediatelyShowMarkdownHelp:true
});
}
});
Sign up or log in
StackExchange.ready(function () {
StackExchange.helpers.onClickDraftSave('#login-link');
});
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
StackExchange.ready(
function () {
StackExchange.openid.initPostLogin('.new-post-login', 'https%3a%2f%2faviation.stackexchange.com%2fquestions%2f61851%2fairplane-gently-rocking-its-wings-during-whole-flight%23new-answer', 'question_page');
}
);
Post as a guest
Required, but never shown
1 Answer
1
active
oldest
votes
1 Answer
1
active
oldest
votes
active
oldest
votes
active
oldest
votes
$begingroup$
I can give you two theories. One is it's a very very mild case of "overcontrolling" of the autopilot roll servo as it chases a perfectly wings level condition and continuously applies a teeny bit too much left, ooops, then a teeny bit too much right, oops, and back and forth.
The aileron control circuit is cables running to hydraulics at the ailerons, with a spring loaded roller in a curvy V shaped cam device that centers each side of the aileron cable circuit. The breakout force to move the control circuit out of neutral (forcing the roller from the center V of the cam) is fairly high and this can actually be a problem for pilots hand flying at higher speeds where the ailerons are quite snappy - applying enough force to break out the circuit and move the wheel left gives too much, and back the other way... too much... and back and forth you go. It can be a pain.
The autopilot servo is basically a little electric winch connected into the aileron cable circuit, doing the same thing the pilot does. It could be that something in the electronic control loop, or mechanically within the servo, can cause this back and forth oscillation on some airplanes, sometimes. It may be related to wear and backlash within the autopilot servo.
The other theory is it's more or less something similar, but in the yaw mode with the yaw damper not able to fully dampen out a dutch roll mode because the amplitude was within the yaw damper's sensitivity band. Dutch roll is rolling due to yaw, which in swept wing jets is very strong, such that it can set up continuous self energizing oscillation. It could also be related to wear and backlash in the yaw damper actuator, which is a pair of electric linear actuators (little electric screw jacks), in the push rods going to the rudder hydraulics.
If you saw the wing tip just going straight up and down, it's mostly likely the first theory. If you could see the winglet moving in a little circle (indicating rolling and yawing), it's more likely the second theory.
I can really only theorize because the issue was never fully explored on the RJ program as this phenomenon was random, very minor and not dangerous, and was never complained about by operators because only someone sitting near the wings that can look straight out at the winglet ever notices it. It was never bad enough to get anyone sick for example, at least on the RJ fleet.
$endgroup$
add a comment |
$begingroup$
I can give you two theories. One is it's a very very mild case of "overcontrolling" of the autopilot roll servo as it chases a perfectly wings level condition and continuously applies a teeny bit too much left, ooops, then a teeny bit too much right, oops, and back and forth.
The aileron control circuit is cables running to hydraulics at the ailerons, with a spring loaded roller in a curvy V shaped cam device that centers each side of the aileron cable circuit. The breakout force to move the control circuit out of neutral (forcing the roller from the center V of the cam) is fairly high and this can actually be a problem for pilots hand flying at higher speeds where the ailerons are quite snappy - applying enough force to break out the circuit and move the wheel left gives too much, and back the other way... too much... and back and forth you go. It can be a pain.
The autopilot servo is basically a little electric winch connected into the aileron cable circuit, doing the same thing the pilot does. It could be that something in the electronic control loop, or mechanically within the servo, can cause this back and forth oscillation on some airplanes, sometimes. It may be related to wear and backlash within the autopilot servo.
The other theory is it's more or less something similar, but in the yaw mode with the yaw damper not able to fully dampen out a dutch roll mode because the amplitude was within the yaw damper's sensitivity band. Dutch roll is rolling due to yaw, which in swept wing jets is very strong, such that it can set up continuous self energizing oscillation. It could also be related to wear and backlash in the yaw damper actuator, which is a pair of electric linear actuators (little electric screw jacks), in the push rods going to the rudder hydraulics.
If you saw the wing tip just going straight up and down, it's mostly likely the first theory. If you could see the winglet moving in a little circle (indicating rolling and yawing), it's more likely the second theory.
I can really only theorize because the issue was never fully explored on the RJ program as this phenomenon was random, very minor and not dangerous, and was never complained about by operators because only someone sitting near the wings that can look straight out at the winglet ever notices it. It was never bad enough to get anyone sick for example, at least on the RJ fleet.
$endgroup$
add a comment |
$begingroup$
I can give you two theories. One is it's a very very mild case of "overcontrolling" of the autopilot roll servo as it chases a perfectly wings level condition and continuously applies a teeny bit too much left, ooops, then a teeny bit too much right, oops, and back and forth.
The aileron control circuit is cables running to hydraulics at the ailerons, with a spring loaded roller in a curvy V shaped cam device that centers each side of the aileron cable circuit. The breakout force to move the control circuit out of neutral (forcing the roller from the center V of the cam) is fairly high and this can actually be a problem for pilots hand flying at higher speeds where the ailerons are quite snappy - applying enough force to break out the circuit and move the wheel left gives too much, and back the other way... too much... and back and forth you go. It can be a pain.
The autopilot servo is basically a little electric winch connected into the aileron cable circuit, doing the same thing the pilot does. It could be that something in the electronic control loop, or mechanically within the servo, can cause this back and forth oscillation on some airplanes, sometimes. It may be related to wear and backlash within the autopilot servo.
The other theory is it's more or less something similar, but in the yaw mode with the yaw damper not able to fully dampen out a dutch roll mode because the amplitude was within the yaw damper's sensitivity band. Dutch roll is rolling due to yaw, which in swept wing jets is very strong, such that it can set up continuous self energizing oscillation. It could also be related to wear and backlash in the yaw damper actuator, which is a pair of electric linear actuators (little electric screw jacks), in the push rods going to the rudder hydraulics.
If you saw the wing tip just going straight up and down, it's mostly likely the first theory. If you could see the winglet moving in a little circle (indicating rolling and yawing), it's more likely the second theory.
I can really only theorize because the issue was never fully explored on the RJ program as this phenomenon was random, very minor and not dangerous, and was never complained about by operators because only someone sitting near the wings that can look straight out at the winglet ever notices it. It was never bad enough to get anyone sick for example, at least on the RJ fleet.
$endgroup$
I can give you two theories. One is it's a very very mild case of "overcontrolling" of the autopilot roll servo as it chases a perfectly wings level condition and continuously applies a teeny bit too much left, ooops, then a teeny bit too much right, oops, and back and forth.
The aileron control circuit is cables running to hydraulics at the ailerons, with a spring loaded roller in a curvy V shaped cam device that centers each side of the aileron cable circuit. The breakout force to move the control circuit out of neutral (forcing the roller from the center V of the cam) is fairly high and this can actually be a problem for pilots hand flying at higher speeds where the ailerons are quite snappy - applying enough force to break out the circuit and move the wheel left gives too much, and back the other way... too much... and back and forth you go. It can be a pain.
The autopilot servo is basically a little electric winch connected into the aileron cable circuit, doing the same thing the pilot does. It could be that something in the electronic control loop, or mechanically within the servo, can cause this back and forth oscillation on some airplanes, sometimes. It may be related to wear and backlash within the autopilot servo.
The other theory is it's more or less something similar, but in the yaw mode with the yaw damper not able to fully dampen out a dutch roll mode because the amplitude was within the yaw damper's sensitivity band. Dutch roll is rolling due to yaw, which in swept wing jets is very strong, such that it can set up continuous self energizing oscillation. It could also be related to wear and backlash in the yaw damper actuator, which is a pair of electric linear actuators (little electric screw jacks), in the push rods going to the rudder hydraulics.
If you saw the wing tip just going straight up and down, it's mostly likely the first theory. If you could see the winglet moving in a little circle (indicating rolling and yawing), it's more likely the second theory.
I can really only theorize because the issue was never fully explored on the RJ program as this phenomenon was random, very minor and not dangerous, and was never complained about by operators because only someone sitting near the wings that can look straight out at the winglet ever notices it. It was never bad enough to get anyone sick for example, at least on the RJ fleet.
answered 1 hour ago
John KJohn K
23.5k13368
23.5k13368
add a comment |
add a comment |
Thanks for contributing an answer to Aviation Stack Exchange!
- Please be sure to answer the question. Provide details and share your research!
But avoid …
- Asking for help, clarification, or responding to other answers.
- Making statements based on opinion; back them up with references or personal experience.
Use MathJax to format equations. MathJax reference.
To learn more, see our tips on writing great answers.
Sign up or log in
StackExchange.ready(function () {
StackExchange.helpers.onClickDraftSave('#login-link');
});
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
StackExchange.ready(
function () {
StackExchange.openid.initPostLogin('.new-post-login', 'https%3a%2f%2faviation.stackexchange.com%2fquestions%2f61851%2fairplane-gently-rocking-its-wings-during-whole-flight%23new-answer', 'question_page');
}
);
Post as a guest
Required, but never shown
Sign up or log in
StackExchange.ready(function () {
StackExchange.helpers.onClickDraftSave('#login-link');
});
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
Sign up or log in
StackExchange.ready(function () {
StackExchange.helpers.onClickDraftSave('#login-link');
});
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
Sign up or log in
StackExchange.ready(function () {
StackExchange.helpers.onClickDraftSave('#login-link');
});
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
$begingroup$
Sounds like the dutch roll mode was working. Were you high and fast at the time?
$endgroup$
– MikeY
2 hours ago